These two repaints represents two Liberty XL-2 used by the Averett Unitversity Aviation Department in pilot instruction. They are for the payware Eaglesoft Liberty XL-2 for FSX only.
My thanks to the Averett Aviation Department staff for allowing me to do a full walk-around and interior shot to give you the best example I could. Sadly, the spats cannot be removed and for authenticity, they should be for the Averett aircraft.
Caz Dalton
NOTE: This package has been modified on 03/28/2011 to include the following update from Cazzie...
Wouldn't you know it, I mess up not one, but both of the main textures for my Averett University Liberty XL-2 for the Eaglesoft Liberty XL-2 for FSX. My thanks to doublecool for catching it. In my haste, I left a layer uncheck that included the landing light, oil cap cover, and oil cap detail. I doubt few would even catch the last two, I did, after I saw the missing landing light after dc's HU in tjhe XL-2 post.
So included in the zip are two new main fuselage textures along with their respective spec textures. I also saw that I did not Multiply the Blending Options on my seat inserts to meld the fabric and show the seams. I amended that also and included a new interior texture to each aircraft for that. There is nothing to alter in the aircraft.cfg unless your tires sink a bit low in the pavement. If they do, change the values in the contact points where the bold red is.
[contact_points]
point.0=1, 1.55, 0.0, -3.75, 1181.1, 0, 0.523, 44.0, 0.24, 2.8, 0.600,
0, 0, 0, 165.0, 165.0
point.1=1, -4.60, -3.0, -3.77, 1574.8, 1, 0.523, 0.00, 0.30, 2.5, 0.600,
0, 0, 0, 165.0, 165.0
point.2=1, -4.60, 3.0, -3.77, 1574.8, 2, 0.523, 0.00, 0.30, 2.5, 0.600,
0, 0, 0, 165.0, 165.0
Thanks for putting up with my mishaps.
Modified by the SOH librarian..."Rami"
My thanks to the Averett Aviation Department staff for allowing me to do a full walk-around and interior shot to give you the best example I could. Sadly, the spats cannot be removed and for authenticity, they should be for the Averett aircraft.
Caz Dalton
NOTE: This package has been modified on 03/28/2011 to include the following update from Cazzie...
Wouldn't you know it, I mess up not one, but both of the main textures for my Averett University Liberty XL-2 for the Eaglesoft Liberty XL-2 for FSX. My thanks to doublecool for catching it. In my haste, I left a layer uncheck that included the landing light, oil cap cover, and oil cap detail. I doubt few would even catch the last two, I did, after I saw the missing landing light after dc's HU in tjhe XL-2 post.
So included in the zip are two new main fuselage textures along with their respective spec textures. I also saw that I did not Multiply the Blending Options on my seat inserts to meld the fabric and show the seams. I amended that also and included a new interior texture to each aircraft for that. There is nothing to alter in the aircraft.cfg unless your tires sink a bit low in the pavement. If they do, change the values in the contact points where the bold red is.
[contact_points]
point.0=1, 1.55, 0.0, -3.75, 1181.1, 0, 0.523, 44.0, 0.24, 2.8, 0.600,
0, 0, 0, 165.0, 165.0
point.1=1, -4.60, -3.0, -3.77, 1574.8, 1, 0.523, 0.00, 0.30, 2.5, 0.600,
0, 0, 0, 165.0, 165.0
point.2=1, -4.60, 3.0, -3.77, 1574.8, 2, 0.523, 0.00, 0.30, 2.5, 0.600,
0, 0, 0, 165.0, 165.0
Thanks for putting up with my mishaps.
Modified by the SOH librarian..."Rami"
