B-25C - MITCHELL
Generic
CFS3 - V4.00.164
AvHistory 1% Aircraft General Statement and Installation Instructions
Gregory Pierson's Version 4.0 first released in August 2006 represents a complete update of the AvHistory 1% Assembly Line Process (1%ALP). Compared to our previous efforts, 4.0 is an order of magnitude improvement and a closer step towards our goal of producing aircraft that perform within 1% of the real aircraft. For additional info on Version-4 flight packages see the included AvHistory - Version-4 1%ALP text file.
No AvHistory 1% aircraft maybe provided for download from any site without express written consent of AvHistory. No skins for AvHistory aircraft, other then those based on stock MS CFS3 visuals, maybe offered for download with our written permission.
Additionally, direct linking to our download site is forbidden.
B-25C - MITCHELL
This aircraft was built by GregoryP using version 4.00.164 of the AvHistory 1% Assembly Line process based on the initial work of Dan DEEDS Walter .
The MS stock visual is used.
The plane was painted by Tom “Animal” Stovall to represent a generic early B-25C. The original templates of default aircraft from Microsoft CFS3 were also created by Tom.
"ARTMAG" provided the custom AvHistory B-25 cockpit with our logo behind the copilots seat.
The B-25C was the first version of the Mitchell to be mass-produced. Following the completion of the initial B-25, B-25A, and B-25B contracts, a number of contracts were awarded to North American for 1625 B-25Cs to be built at its Inglewood factory. At the same time, an additional contract was issued for 2290 essentially identical B-25Ds, to be built at a new North American plant in Kansas City, Kansas.
The B-25C was outwardly almost identical to the B-25B. It introduced the R-2600-13 Double Cyclone engine with Holley 1685HA carburetors in place of the earlier Bendix Stromberg PD-13E-2 units. The Bendix carburetors were favored because of their easier maintenance, but they required more careful anti-icing procedures. De-icer and anti-icing systems were added, and a Stewart-Warner cabin heater was added in the left wing. A 24-volt electrical system was also added.
The armament of the B-25C was the same as that of the B-25B, namely a single 0.30-inch machine gun in the nose, two 0.50-inch machine guns in the dorsal turret, and two 0.50-inch machine guns in a retractable ventral turret. The ventral turret was often removed in the field.
The B-25C introduced a new type of tail skid underneath the extreme rear fuselage, a solid unit which replaced the spring-loaded tail skid of earlier versions. This type of tail skid was retained throughout the Mitchell production run.
Generic
CFS3 - V4.00.164
AvHistory 1% Aircraft General Statement and Installation Instructions
Gregory Pierson's Version 4.0 first released in August 2006 represents a complete update of the AvHistory 1% Assembly Line Process (1%ALP). Compared to our previous efforts, 4.0 is an order of magnitude improvement and a closer step towards our goal of producing aircraft that perform within 1% of the real aircraft. For additional info on Version-4 flight packages see the included AvHistory - Version-4 1%ALP text file.
No AvHistory 1% aircraft maybe provided for download from any site without express written consent of AvHistory. No skins for AvHistory aircraft, other then those based on stock MS CFS3 visuals, maybe offered for download with our written permission.
Additionally, direct linking to our download site is forbidden.
B-25C - MITCHELL
This aircraft was built by GregoryP using version 4.00.164 of the AvHistory 1% Assembly Line process based on the initial work of Dan DEEDS Walter .
The MS stock visual is used.
The plane was painted by Tom “Animal” Stovall to represent a generic early B-25C. The original templates of default aircraft from Microsoft CFS3 were also created by Tom.
"ARTMAG" provided the custom AvHistory B-25 cockpit with our logo behind the copilots seat.
The B-25C was the first version of the Mitchell to be mass-produced. Following the completion of the initial B-25, B-25A, and B-25B contracts, a number of contracts were awarded to North American for 1625 B-25Cs to be built at its Inglewood factory. At the same time, an additional contract was issued for 2290 essentially identical B-25Ds, to be built at a new North American plant in Kansas City, Kansas.
The B-25C was outwardly almost identical to the B-25B. It introduced the R-2600-13 Double Cyclone engine with Holley 1685HA carburetors in place of the earlier Bendix Stromberg PD-13E-2 units. The Bendix carburetors were favored because of their easier maintenance, but they required more careful anti-icing procedures. De-icer and anti-icing systems were added, and a Stewart-Warner cabin heater was added in the left wing. A 24-volt electrical system was also added.
The armament of the B-25C was the same as that of the B-25B, namely a single 0.30-inch machine gun in the nose, two 0.50-inch machine guns in the dorsal turret, and two 0.50-inch machine guns in a retractable ventral turret. The ventral turret was often removed in the field.
The B-25C introduced a new type of tail skid underneath the extreme rear fuselage, a solid unit which replaced the spring-loaded tail skid of earlier versions. This type of tail skid was retained throughout the Mitchell production run.
