Black water.

Anthin

Anthin

Charter Member
I have a large problem. I downloaded the new FSWC water config.
from Striking software. Tried one of their presets and now the water
has turned jet black. I have been trying everything I can think of
without any luck. Any ideas on how I could fix this. water is still ok
in DX9.
Here's hoping.
Anthin.
 
Try reloading the Water Options in DX10 Fixer's control panel. If that simple fix fails you might have to delete the Shaders10 folder and let the sim rebuild it (will happen automatically the next you you open the sim).

HTH

Greg
 
It's at: C:/User/(Your Name)/AppData/Local/Microsoft/FSX. Just delete the Shaders10 folder, then go fly in FSX.

Greg
 
Greg. I have tried that path but I keep getting not Local Roaming and a message says cant find it.
my flight sim is on my E drive.


Anthin
 
Do you have a "Users" folder on the root of the E: drive? If so, try there. Also, a search should yield the location... there are only two folders in that specific FSX folder: Shaders (DX9) and Shaders10 (DX10). No need to delete the Shaders folder, just the Shaders10.

Greg
 
Finally found the Shaders 10 and deleted them
Started the sim,still Black water. Also a large patch of white water.
Will try again.

Anthin
 
I'm curious what happens if you now go into the DX10 Fixer and reapply the Water Options?

Greg

Edit: Also, did you configure using FSWC+'s DX10 settings?
 
Yes I did
My warer button is greyed out in the fixer.
Is there a way to reinstall it wit the button
not greyed out?

Anthin
 
Might be time time to consider removing FSWC+... just to test the situation. You say the water is fine in DX9, so perhaps removing the program, then deleting the Shaders10 folder and re-applying DX10 Fixer's Water Options.

Others here have added FSWC+ and are running fine in DX10, so hopefully they can weigh in on this issue.

Greg

Edit: Just saw where you added the greyed out Water Options button in DX10 Fixer. Just uninstall then reinstall the Libraries... the button is near the top of the Fixer's page.
 
I hope you get this sorted Anthin. I am using the new water configurator with the "North Atlantic" preset. I had to tweak the settings a bit to get things to my liking but I love it so far. I did have to reload the shaders a couple times because I had apparently "over adjusted" the sliders. It says on the Striking Software site that one known issue is the ranges are not tuned. To get the results I wanted I had to use VERY MODEST slider movement. I had made some pretty drastic adjustments and lost all my reflections and wave action. I just reloaded the "North Atlantic" preset and started tweaking again using smaller adjustments. I hope this helps you a bit.


Known issues:


  • Water modification ranges have not been tuned and may result in dramatic changes.

 
A heartfelt Hi to you Corpse Grinder.

Yeaaaaaaa!
that was it!. OMG. I reduced sliders to zero. Water does not look great
but from here I can tinker around and get them back to what I had before.
What a relief. I came very close to girding my loins for the dreaded re-install.
And a thanks to greg for his help.

With many thanks . Anthin.:jump::running::redfire:
 
Anthin said:
A heartfelt Hi to you Corpse Grinder.

Yeaaaaaaa!
that was it!. OMG. I reduced sliders to zero. Water does not look great
but from here I can tinker around and get them back to what I had before.
What a relief. I came very close to girding my loins for the dreaded re-install.
And a thanks to greg for his help.

With many thanks . Anthin.:jump::running::redfire:
Click to expand...

So glad you got it sorted Anthin! I'm glad I could be a bit of help. I have not really been active on these forums for quite some time. Back in the early 2000's I was really active in the CFS3 modding community, but since then I have been over at FSEconomy for the past several years and I am a Pilot Service Rep (forum admin) over there. You should stop by some time if you fancy some GA flying. A pleasure to meet you as well sir!

Happy Landings!

~Justin
 
A real pleasure to meet you Justin. As yet I have not been able to change greyish water textures
but it maybe a start. My poor old heart can't hope with these problems cropping up recently.
If you can think of a way I can improve water textures it would be great.

So far I have been unable to change the texture. If that is the case I will accept my current texture
and continue on.
Anything is prefable to a complite reinstallI . I am so glad to be a member here at the Outhouse.

Thank you.

Anthins blood pressure slowly dropping. LOL.

:applause:
 
If your texture is grey, perhaps adjusting the saturation slider in FSWC might help. I believe this adjusts the over all texture color.

~Justin
 
Bad news Justin, I now have White water.! I tried to change water texture
with fswc lite and now it has become a nightmare. I have no ideas anymore.
I did try adjusting sliders but nothing happened.

Anthin.
 
You must log in or register to reply here.
Back
Top