• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

Captain Sim / XLoad F/A-18D Improvements - FSX

delta_lima

delta_lima

Charter Member 2015
Hey all,

With the recent release of the FSXBA F/A-18C, there's been some chatter on bringing in the VC to FSX.

Here's what I've discovered so far:

VC transplant from the D model, requires no change to the eyepoint coordinates. Bring over the panel, swap out the interior .mdl and rename to the original.

While most systems (maybe all, haven't gone through all) appear to work, I get an FCS error related to the F18.dll With that .dll present, am not sure why - will dig further.

I have no stores configurator - still working on that.

Canopy texture is very light, almost invisible in FSX-A + DX10. I've tried substituting textures from the FSXBA, but not yet successful.

If you have any tips or mods that have worked on the D model, please feel free to share. I'll post my results as I get them.

cheers,

dl
 
With the recent release of the FSXBA F/A-18C, there's been some chatter on bringing in the VC to FSX.
Click to expand...
The FSXBA F/A-18C has an FCS system designed for FSX/P3D 32 bit, and another, different one for P3D 64 bit. And never the twain shall meet. As long as you have the correct ancillary files for it to function, it should work flawlessly. Naturally, that's for the F/A-18C it's self, with the correct Panel folder, aircraft.cfg and .air files, and Model folder.
Other than that, it should work fine in another plane :pirate:

Good luck. I will do what I can to help, but I won't mention the D Model to Jimi!
THAT is a no-no, big time. :banghead:

Pat☺
 
Just remembered something (I'm not at the PC, so I hope I've got this right!).
There's an entry in the aircraft.cfg that needs copying across from the FSX BA to the CS D.
Without it you'll get the FCS fail message. I basically copied all the aircraft.cfg except contact points so the FD would be the same.
 
Thanks Dave - copying all the .cfg contents did the trick. No FCS error now.

What I now have is the refueling probe extends on gear down - sounds like there's an animation conflict somewhere.

And the canopy texture is still almost invisible. I'm starting to think that's a model, and not a texture issue.

Will keep tinkering.

dl
 
The two really critical sections are the [flight_tuning] , and, MOST important, [HornetFCS] . That contains the settings for the PID controllers in the FCS system.
I'll wager that was what was holding you back, but hey, I may well be wrong.
The [Electrical] section has to match too.
The [Effects] and [SmokeSystem] are needed as well, to get the effects to show properly.
Finally, the [flaps.X], [airplane_geometry], and [autopilot] sections, although the [autopilot] MAY be optional, I am not certain.

I guess the easiest is just copy the whole aircraft.cfg and .air files over, except the [Contact_Points]...
:biggrin-new:

Glad you got it going, anyway :triumphant:
Pat☺
 
You must log in or register to reply here.
Back
Top