I need help on my planes

P

Pere

Members +
Hello everyone, I am writing to you because I would like someone to help me, all my P3D v4 planes have an unusual tendency to lift the nose and I have a hard time keeping the flight level, I have calibrated my joystick again and I keep on happening. Same with all my planes, although his trimado this in 0º I have no idea that it can happen, some idea ?, thank you very much and they forgive that I can not write better but I do it through google translator
Hello everyone, I am writing to you because I would like someone to help me, all my P3D v4 planes have an unusual tendency to lift the nose and I have a hard time keeping the flight level, I have calibrated my joystick again and I keep on happening. Same with all my planes, although his trimado this in 0º I have no idea that it can happen, some idea ?, thank you very much and they forgive that I can not write better but I do it through google translator
 
Hi Pere,

I have not installed P3D4 yet, but I my installation of P3D3.4 I found that every time I started a new flight from "cold and dark" that my trim settings were maximum nose-up, and if I failed to reset them it would be a handful on take-off.

Verify your trim setting before flight.

JKH
 
Hola Pere,

no he instalado P3D4 todavía, pero tengo mi instalación de P3D3.4 me encontré con que cada vez que empecé un nuevo vuelo de "frío y oscuro" que los ajustes de ajuste eran nose-up, Y si no los restablezco Sería un puñado en despegue

Compruebe el ajuste del ajuste antes del vuelo.

JKH [/ QUOTE]

Gracias por su respuesta, pero ese no es el problema, me caliento el motor en marcha con A2A cessna Avance el acelerador y cuando me despegue, necesito 17% de trim para no subir más, y así sucesivamente Todos mis aviones : mareado :: mareado:
 
Hi Pele,

I do not read Spanish well, but I did see 17.5 degrees of trim setting. WAY too much, almost maximum. Start at 3 degrees or thereabouts, depending upon your load and see what works best. You can always start at 0 degrees as well for a reference point.

JKH
 
If trim is not the problem, you could also check the calibration of your joystick or other controller. Maybe it is giving you a nose up input.
 
When strange things like this happen, try deleting your default flight. Many times a corrupt saved state will persist from one flight into the next four what seems like no reason.
 
[QUOTE = scotth6; 1099307] Si el ajuste no es el problema, también puede comprobar la calibración de su joystick u otro controlador. Tal vez le esté dando una entrada de nariz. [/ QUOTE]
Many thanks for your answer, my Joystik is an old Cyborg 3D golden edition of Saitek, I have never had problems with it and no button or lever is used to trip the plane, even so I calibrated the Joy .. 2 times, the strange thing is That happens to me with ALL my planes, from the moment of takeoff, I have always controlled the trim externally to joysyick, so i is a problem common to all planes but not to the Joystick.
 
[QUOTE = 000rick000; 1099313] Cuando suceden cosas extrañas como estas, intente eliminar su vuelo predeterminado. Muchas veces un estado guardado corrupto persistirán de una fuga en los próximos cuatro lo que parece ser ninguna razón. [/ Quote] [/ quote]


Voy a tratar de responder a usted tan pronto como me sea posible, muchas gracias


Click to expand...
 
I dont' have P3D but I bet it's an 'AUTO PILOT' problem. Or rather, missing lines in aircraft's cfg that prevent AP from going into 'Alt Hold' as default 'condition' when you activate AP. This would cause AP to start inputing up pitch trim as it tries to 'attain' the alt setting you input on panel even though you are at gate! You can turn off AP and reset trim to '0'. Or you can add these lines (as not all have them) to (autopilot) section in aircraft cfg:

use_no_default_bank=1
use_no_default_pitch=1
default_pitch_mode=0
default_bank_mode=0

Chuck B
Napamule
 
You must log in or register to reply here.
Back
Top