• Please see the most recent updates in the "Where did the .com name go?" thread. Posts number 16 and 17.

    Post 16 Update

    Post 17 Warning old domain name stealing credentials

  • Special Server Maintenance

    Just when you think you have everything running some what better...

    You get a message from the Hosting company. Short story they need to move us to a new server. I have been working with them to plan a good date for all concerned. Here is what we have come up with as a schedule.

    1. November 4th 17:00 -5UTC shut off the forums and start backup proceedures. During this time there will be no access to the forums or the Resource Section.
    2. November 5th Continue with Backups and download same until complete.
    3. November 6th 7:00 turn over server to hosting company to move system to new server
    4. November 7th - 8th restore backups and upgrade forum software.

    If all goes well we should be back online on November 8th.

    To keep you updated we will post updates on AVSIM forums.

    Thank you for your support.

MCX Question

Duckie

Duckie

SOH-CM-2024
Is it possible to change the material color in a model using MCX? This change would be for personal use only. I'm just tired of flying around with fuselage signal lights that are colored bright lime green, florescent yellow, and florescent red! They really detract from an otherwise descent looking model.

The colors for the lights are in the model and show up in MCX. I've identified the colors and can change them but the model exports with errors.

Thanks in advance for your help,

Steve
 
I wish that was possible however I think the only option is "MDLMat", which. . .if you can locate the correct material, allows you to change the color and save it back to the mdl file. I've tried it in the past, but it's like looking for a needle in a haystack. There may be as many as 20 or more material colors for the exterior and you have to find the one that you're looking for. If it's a very uncommon color then you may be lucky enough to discover there's only one material in that whole lot that happens to have that color, but that's not always the case.

Changing it in MCX would be so much easier because MCX pinpoints the exact color for the exact position it occupies, but then you have to save back to the mdl file and if there were any errors when loading it (they show up as MCX is reading the mdl), then those errors (as you've discovered) are saved back to the mdl and your airplane is toast.
 
UPDATE:

Ed I went back and looked at it in MDLMat and it only had 34 colors and of those there were only 2 reds, 2 greens, and 1 "yellow".

So now my signal lites are not nearly as noticeable as they were before. Thanks for the reminder about MDLMat. I hadn't used it since my FS9 days and I had never even unzipped the FSX version!

Thanks again,
Steve
 
Duckie said:
UPDATE:

Ed I went back and looked at it in MDLMat and it only had 34 colors and of those there were only 2 reds, 2 greens, and 1 "yellow".
So now my signal lites are not nearly as noticeable as they were before. Thanks for the reminder about MDLMat. I hadn't used it since my FS9 days and I had never even unzipped the FSX version!

Thanks again,
Steve
Click to expand...
Excellent! Glad it worked for you Steve!
 
Two things. First, are these nav lights? if so you can swap them for better ones. I tend to use the Milviz ones when I make lighting changes. Second, if the lights have visibility conditions, making changes with the visibility conditions in place can screw up the model badly. You could try setting the visibility conditions to 'none', make the changes, save and exit MCX. Open up again, make the visibility condition changes and save. It's a trick Henk (hschuit) taught me a few months ago; for years I'd get corrupted models if I tried making too many changes to models, especially where weapons with loadout visibility conditions were involved. MCX seems to hate changes being made to parts with visibility conditions active. Worth a try - no guarantees!
 
DaveQ said:
Two things. First, are these nav lights? if so you can swap them for better ones. I tend to use the Milviz ones when I make lighting changes. Second, if the lights have visibility conditions, making changes with the visibility conditions in place can screw up the model badly. You could try setting the visibility conditions to 'none', make the changes, save and exit MCX. Open up again, make the visibility condition changes and save. It's a trick Henk (hschuit) taught me a few months ago; for years I'd get corrupted models if I tried making too many changes to models, especially where weapons with loadout visibility conditions were involved. MCX seems to hate changes being made to parts with visibility conditions active. Worth a try - no guarantees!
Click to expand...

Hi Dave. Thanks for the tip. It was just a diffuse color change only, the static ingame daylight (lights off) display and I used MDLMatXX to make the changes. They are the landing signal lights, bottom aft fuselage. The stock colors were so bright, very distracting, and you definitely wouldn't take a screen shot with those lights showing. I almost decided to uninstall it but gave it one more try. There doesn't seem to be any negative effects of the change that I've seen so far.
 
This seems interesting and I'd like to try it on the visors of the Flight1 Islander. Can someone please post a like to the MDLMat utility.
I've scoured Martin Wright's website (that it is Martin is an assumption on my part) but cannot find a working link to download.
Thanks in advance.
:ernaehrung004:
 
FS,
You need the MDLMatXX (about halfway down that list) not just the MDLMat prog, for FSX work.

Cheers

Shessi
 
Shessi said:
FS,
You need the MDLMatXX (about halfway down that list) not just the MDLMat prog, for FSX work.

Cheers

Shessi
Click to expand...
Yep, spotted that. Thanks.

Turns out the visor color in the Islander is a texture so that's an easy fix.
But hadn't heard of Martin's MDLMat utility so I'm glad this thread was started.
:ernaehrung004:
 
You must log in or register to reply here.
Back
Top