• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

Modifying the aircraft.cfg file

S

Sid2008

Charter Member
Hi friends,
Just seeking some quick guidance. I have owned a copy of Abacus' Fly the airbus Fleet for a while. The landing characteristics and roll rates on their A-318 is simply terrible and unrealistic.

I have much better behaved freeware A-318s for FS9, and i was wondering what lines in the aircraft.cfg file should i copy from the well benahed a-318 into the abacus A-318 to make the latter fly and land like their former?

Thank you,
Sid
 
Instead of doing that, try using the .air file instead. Copy and rename it. Save a copy of the original.

The air file has all the flight characteristics built into its tables. The cfg file simply allows you to tweak them.
 
I would also copy over the aircraft.cfg file, after renaming the original one aircraft_old.cfg. It also contains lots of flight dynamics information.

Here's how I do it:

1. Back up the plane's folder to another location for safekeeping.

2. Rename the aircraft.cfg file to aircraft_old.cfg

3. Copy the AIR file and the aircraft.cfg file of the plane that flies properly into the plane's folder.

4. Open both the copied aircraft.cfg file and the aircraft_old.cfg file using Notepad or Wordpad.

5. Copy the top sections of the aircraft_old.cfg file (headed by fltsim.0, fltsim.1, etc.) and overwrite the same part of the aircraft.cfg file.

6. Copy the following sections from the aircraft_old.cfg file and paste them over the same sections in the aircraft.cfg file, replacing them:

a. Contact Points
b. Lights
c. Views
d. Effects (if desired)
e. General (if desired)

7. Copy the sim= line from the aircraft.cfg file *of the plane that flies properly* and paste into all the sim= lines of the new aircraft.cfg file.

8. Save the new aircraft.cfg file. Restart FS.

Now that aircraft should fly like the other plane.

If the COG and reference datum positions of both planes are not the same (in the Weight and Balance section, usually 0,0,0), then this method will not work without a lot more work, but this is unusual (except for the default aircraft).

Hope this helps,
 
Milton Shupe said:
Instead of doing that, try using the .air file instead. Copy and rename it. Save a copy of the original.

The air file has all the flight characteristics built into its tables. The cfg file simply allows you to tweak them.
Click to expand...


How can you do this? I thought the air file needed a special program to open and modify it.
 
In this case, there's no need to modify the air file - just copy one of the freeware air files into your Abacus folder, make a backup of Abacus' original, then rename the freebie to match the original so that the cfg can find it.

If you want to edit the air files, look on Flightsim.com for aamv22.zip. It's not that hard to edit most things, but you can really get one knotted up if you're not careful. Just remember to backup your original and you'll be safe to play around.
 
You must log in or register to reply here.
Back
Top