• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

Profiling - G940

T

Timm

Guest
Hi Guys,
Need some help/info please on profiling with the G940. Now in FSX I fly all types of Aircraft ranging from the little Piper Cub to The Bell 412 and the L-39 Albatros, and as you all know these all have different commands etc, now with my old Saitek X52 I was able to make a profile for each of these aircraft and I was able just to switch the profile to the aircraft I was flying. Now for some reason or is it just me you can't do that with the G940 ?
What I have done so far is made a profile for the L-39 which works great and now I want to make one for the Cera Bell 412 it's telling me that this will over write the L-39 as it's asking for the same exe.file. Any help will be greatfull.
One thought I have just had is I don't use the mode switch so I might just assign the 3 aircraft I fly most via this. In other words use Mode 1 for the Albatros, 2 for the Bell 412 and 3 for the Piper Cub. Unless there is another way. Timm
 
There is what I call an issue with the G940. The buttons are programmed via the Logitech Profiler while the axes, stick, throttles, rudder and brakes, are controlled via the FSX controls settings. The place that really binds is four engine aircraft that need differential thrust due to a non-steerable tail-wheel. There is no way to tell it right side/left side/one throttle all engines, vs a twin two engine config. I tried to set up three FSX configs with different throttle settings. It didn't work.
 
Hi Glenn,
It's sure has some problems. I only fly the aircraft I mentioned above but most of the time I fly the L-39. I am going along the lines of profiling these 3 aircraft via the mode switch. I done the L-39 and the Bell 412 so far there flying just as I want them. Timm
 
Gents,

I understand that you are having troubles with these configuration, mainly due to a lack of knowledge; perhaps, because the manual is "lacking" in appropriate documentation.

I can tell you that it is possible to do what you'll want WITHOUT using FSUIPC or "mucking" with external FSX utilities/game controller configs. However, you'll have to wait for a week or so as my FSX system is under upgrades and I cannot post screenshots or configurations until it is up again.

Can you'll wait? Or, keep trying for yourselves....
 
Hi James,
Thanks for that info. I'm sure there is away in doing these profiles but as you said the the manual is "lacking" in appropriate documentation. I will look forward to your post. Timm
 
Mr. "Timm,"

OK; I'll do a step by step process for you... and you'll see that it works quite nicely. And I might even post a few extra profiles for you'll to test as well... Will you find that to be useful?
 
Hi, James,

I'm open to suggestions. Someone suggested FSUIPC. I'm a little relunctant to buy it, not because I have had a bad experience of any kind. I know Peter provides excellent support with great patience and dignity. It's more just out of maybe a desire not to "mess up" an already loaded set-up. I'm very happy with the G940 except for the four engine (A2A B-17 mostly) issue.

OK, I've rambled on enough.

Glenn
 
Mr. Glenn "glennc,"

I think I suggested FSUIPC to you for the single axis engine -> 4 axis mapping before. It is something I used before with great success. But, in tinkering with the G940, I discovered much with how this works and found a way to bypass FSUIPC with Axis'. Please be patient as my system is being re-worked and as soon as it is up and going, I can be of some help to all of you.

:wavey:
 
James, thank you - much appreciated. I know how much "fun" rebuilding a PC can be.

Happy Friday

Glenn
 
Will you find that to be useful?
Click to expand...
James,
Anything you do for us will be greatly appreciated and not just for me but I'm sure a number of other guys out there. Whilst on the subject of profiles has anyone made use of the mini button on the stick ? Timm
 
You must log in or register to reply here.
Back
Top