• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

Repairing plateaus

strykerpsg

strykerpsg

SOH-CM-2023
Gents,

A bit frustrated. Got most of the add ons installed but cannot get rid of the elusive plateau at Friday's Harbor field (default FSX flyover point) or the one generated at McChord field (KTCM). It was never there when I originally installed all before and now shows up. Anyway, I would like to just remove Orbx regions, Orbx Global base and FS Global 2010 FTX in hopes of removing the plateaus and reinstall them one by one to avoid the plateaus again. However, I see neither a Uninstall option in their menu or in Control Panel. I plan to do a repair option from the FSX files and leave the REX and additional after market planes installed.

Do you think I am going about this the right way or have I overlooked something? Also, if I must delete all and start over again, I will at least attempt to save the add on aircraft files and avoid that additional headache, just a bit frustrated and I know there's an abundance of KSX knowledge and wisdom.
 
Hi Matt,

It sounds like something is creating an elevation mismatch between your airfields and the local surrounding scenery. First, check to see that 'North America' is checked in FTX Central. I sometimes forget when I just want to get in and fly. It's easy to overlook, and the FTX regions have custom elevation in some cases. Second, go into your Scenery Library under Settings and take a look at the scenery priorities. There may be some other scenery that is overriding PNW, causing the plateaus. You'll want to make sure that the FTX regions have the higher scenery priorities, and it's fairly easy to adjust. Hopefully it's something simple to fix for you.

Also, make sure you have the latest PNW patches, just in case.

Best of luck.

Craig
 
Thanks Craig. I'll play some more tonight with it. I know it has potential to look fantastic and that's absolutely my desired end state.

As for deleting any Orbx stuff, suggestions?
 
I've never uninstalled my Orbx sceneries so I can't suggest anything specific. You might start with the .pdf manuals that came with the sceneries to see if there is a recommended procedure. They also have a support forum on their site where you might have better luck sorting your situation out.
 
Matt, do you have FTX Global Vector installed ?

If so you might need to run the "FTX Global Vector Configuration Tool".
Its under settings in "FTX Central V2".
Click the "Airport Elevation Corrections" tab then the "Run Auto-Configuration" button.
 
Dangerous Beans said:
Matt, do you have FTX Global Vector installed ?

If so you might need to run the "FTX Global Vector Configuration Tool".
Its under settings in "FTX Central V2".
Click the "Airport Elevation Corrections" tab then the "Run Auto-Configuration" button.
Click to expand...

Thanks for the suggestion brother, but it was suggested and tried.....it only brought the entire airfield on a plateau rather than just the runways and taxi ways.

I think the best course is just to remove the Orbx installs, do a stock FSX repair and try it again. I believe the problem arose when I may have misread in the Orbx forums that you can install all the regions together and then start FSX and allow it to rebuild it's database. Lesson learned is next time I will start FSX each time to allow a slower build of the database, in hopes of avoiding the plateaus. I just wish their products would show up in the Control Panel, make it a bit easier to select and clear. Since I will be re-installing, I'm not concerned about the registry being clear of the products, in hopes of avoiding the proof of purchase steps when re-installing.

I posted the same issue on the Orbx forums and downloaded their install guide. Unfortunately the guide does not discuss removal of their products, just the various layers and their interactions and of course, installation. I appreciate, as always, the help and suggestions of this good community.
 
Hello Matt,
Here's something I copied from somebody else and keep in my Orbx library. Uninstalling.......


To uninstall a FTX airport, I'll use YSCH as an example :

FIRST set FTXCentral to [Default]

- Browse to FSX\ORBX\FTX_AU (for American airports browse to FSX\ORBX\FTX_NA instead)
- Delete the FTXAA_YSCH folder

- Browse to FSX\ORBX\Scripts
- Delete orbx_cpl_ysch and scenerylib_AU_YSCH

- Run FTXconfigrator.exe (silent operation, it removes the scenery library entries)

Use the same guide to delete any payware FTX airport.


....................................................


I'll use WLS as an example

FIRST set FTXCentral to [Default]


1 - Browse to FSX\ORBX\FTX_EU
- Delete the 4 x WLS titled folders:
FTX_EU_WLS_05_SCENERY
FTX_EU_WLS_06_CVX
FTX_EU_WLS_07_MESH
FTX_EU_WLS_08_CUSTOM

2 - Browse to FSX\ORBX\Scripts
- Delete scenerylib_EU_WLS
- Run FTXconfigurator.exe (silent operation, it removes the scenery library entries)

3 - Browse to FSX\Scenery\World\Scenery
- Delete all the "WLS" titled files

Use the same guide to delete any Europe FTX regions

..........................................................
 
You must log in or register to reply here.
Back
Top