TigerCat

falcon409

falcon409

Moderator
Staff member
Just a few quick shots of the Tigercat again. I've redone all the textures (enlarged them to 2048x2048 to get better detail). I still have to tone down the panel lines, add some weathering, add some shine to her and a few other tweaks. I'm really enjoying her now.:salute:
 
expat said:
Nice work Falcon. Looking very good.
Click to expand...
Thanks, I toned the panel lines down, then added an alpha channel to put a bit of a shine on it and the airplane went transparent, lol. Apparently, this model was never coded to accept a shine. . .too bad. Oh well, back to the weathering.
 
If the model is freeware, post a link. I've got Jeff "WuhWuzDat" Delhaye's "Shiney" mdlc integration installed, so flipping the reflective switch is no problem as long as the model will accept the change.
 
Falcon

Check your e-mail....I just sent you the MDL file for the F7F-3 with reflective texturing enabled.

OBIO
 
That link is for a FSX conversion?

:kilroy:

Cees

Never mind: I read the other thread now. It's still early here in Holland......
 
Still a WIP, but I wanted to see the results of the modified mdl. Very nice. . .thanks OBIO!!:salute:
 
Obio, can i get that model conversion also? working on a paintkit for it like yourself and want to get this bare metal one looking, well..... metal.... :ernae:

cheers in advance buddy :ernae:
 
I been around a lot of F7-Fs. They had a shine like a new car. A lot brighter than you show.
My Uncle Sam, a Major on the Marine Corps, was the first commander of the Tigercats squadron.
 
Hi,

Perfectly :)
Just some contact points ajustements ....

point.0 = 1, 13.917, 0, -8.2, 1800, 0, 1.05, 45, 0.05, 2.5, 0.8, 6, 4, 0, 170, 225
point.1 = 1, -1.5, -9.75, -7.5, 2000, 1, 1.5, 0, 0.437, 2.5, 0.8, 7, 5, 2, 170, 225
point.2 = 1, -1.5, 9.75, -7.5, 2000, 2, 1.5, 0, 0.437, 2.5, 0.8, 5, 7, 3, 170, 225

Also
prop_anim_ratio=1.2
Give a better visual effect for the props.
 
Tom

The Alpha F7F Tigercat is an FS8/FS9 model. You can download it from the freeware page on the Alphasim site. Does not come with panel or gauges. I uploaded a panel set for the Tigercat some time back....2D and VC panels all done up. I am reworking the panel for FS9 as part of my restoration project....using nicer gauges, modifying the 2D and VC panel images...I enlarged the VC panel image from 512 by 512 to 1024 by 1024 for max clarity and detail.

OBIO
 
Smoothie

The reflective mdl for the F7F-3 day fighter has been sent. I haven't done the tweak to the F7F-3N night fighter yet.

OBIO
 
Thanks buddy just got the e-mail... back to work now and hoping that i can get this nailed down... :ernae:
 
Smoothie,

One thing I have found while doing up a bare metal skin for the Tigercat...on the F7fbndp2.bmp texture sheet...the tail fillett thingie and the lower portions of the rear non-moving prop blades are over lapped. So, when using a light color to paint the plane, if you look at the back side of the non-moving props, you will see the lower half of the prop blades are the same color as the tail fillett thingie.

OBIO
 
ok got most of the fuselage nailed down now, given it a high sheen (Working on 2 Variations, high gloss and low-gloss) and adjusted tonal values for some of the panels to give it a bit of depth... fuselage so far...
 
OBIO said:
Falcon

Check your e-mail....I just sent you the MDL file for the F7F-3 with reflective texturing enabled.

OBIO
Click to expand...

Wouldn't specular gloss be more appropriate? The real ones were finished in glossy paint, not reflective like polished bare metal.
 
You must log in or register to reply here.
Back
Top