Aileron Sensitivity

[Moses03]

Was trying to find this setting in the air file. Not sure which table it is. Thanks- Moses

 

[Flusirainer]

aircraft.cfg

[flight_tuning]
cruise_lift_scalar = 1.0
parasite_drag_scalar = 1.0
induced_drag_scalar = 1.0
elevator_effectiveness = 1.0
aileron_effectiveness = 1.0
rudder_effectiveness = 1.0
pitch_stability = 1.0
roll_stability = 1.0
yaw_stability = 1.0
elevator_trim_effectiveness = 1.0
aileron_trim_effectiveness = 1.0
rudder_trim_effectiveness = 1.0


Airfile with AirEd

View attachment 61853

 

[Dev One]

There are also two graphs:
342 & 518 in the .air file. These can be viewed & modified using AirEd or Aircraft Airfile Manager.
In AirEd move the highlighted shown x value line to the right using the right arrow on keyboard, then calling up the X value by pressing 'x' & the 'Y' value using, surprisingly 'y' & entering the numeric value required.
As always save a copy before modifying!

If one has additional aileron references in the 1500 blocks then these will overwrite the 1100 entries.
HTH
Keith

 

[fliger747]

Moses:

I reccomend Aircraft Airfile Manager for modification of any of the tables that require hex inputs. Table 342 affects the change in effectiveness with airspeed, an important factor in high speed aircraft. Primary Aerodynamics has a roll section which also has a great influence. For instance this is the area where you can set the effect the rudder has on roll (as in the F7F). There are also a number of tables which affect the roll at high AOA and stall/spin values.

AirEd is useful for copying a table over from a different airfile, or even adding a table which might be missing from your airfile.

Good luck! Tom

 

[Dev One]

Table 342 is not only useful for high speed sensitivity, it can also be used for 'sloppiness' near the stall - same goes for the equivalent rudder & most of all the elevator effectiveness near the stall.
Example: the Auster family are well known for their loss in effectiveness of the elevator on landing!
Keith

 

[Dev One]

I made a mistake above! It should be the 517,518,519 blocks that are related to speed for elevator, Aileron & rudder, 342 et al are to increase or decrease the effectiveness with respect to angle of deflection.
Keith

 

[fliger747]

Indeed, the above tables are useful for tuning the handling. For the F4U one would end up turning final into the groove for a deck landing one would end up with the stick over in the corner as aileron ran out of effectiveness for counteracting torque. Same with rudder.

Some aircraft would loose control effectiveness at high speed, an example being the Zero loosing roll effectiveness, or Mach induced elevator issues in say the P47.

One issue we can't simulate directly is control force limitations. At some point manual controls usually had a limitation of control force that could be applied by the pilot. We have to approach these issues indirectly through the speed related tables making them less effective with speed, where as they might be quite effective if the pilot had be a Gorilla.

T

 

[Moses03]

Thanks for the assistance fellas. I have a plan now.:salute:

 

[Ivan]

There is yet another table that changes effectiveness with G-load.

- Ivan.

 

[Flusirainer]

No!!!

342 vs Stick Position

453 vs Speed Mach

518 vs Dynamic Pressure (Dynamic Pressure = IAS^2 x 0.0033485)

1535 vs AOA

 

[fliger747]

Haven't seen a table for effectivness vrs G directly, but of course AOA variable tables such as 1535 and 1538 affect roll. High AOA is not always a high situation, but can be.

T

 

[bstolle]

There is yet another table that changes effectiveness with G-load.

Correct, table 546 = load factor vs aileron effectiveness scalar

 

[Flusirainer]

Correct, table 546 = load factor vs aileron effectiveness scalar

I do not know. I've found it now but in the aam.ini file.
Do you have a text version for AirUpdate? I want to test it.

 

[bstolle]

I don't have AirUpdate, but the default Extra airfile contains that table.

 

[fliger747]

Thanks Bernt, hadn't seen that one as many files don't include that entry.

A note for general interest, .AirEd can be used to add entries from another file that does have the desired tab.

Cheers: T

 

[bstolle]

To be more precise, the default Extra has this table only if you have Acceleration installed (the P-51 used this table as well). The Extra without Accel doesn't have it...