• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

Air File Assist Please

FOO FIGHTER

Charter Member
I adjusted the contact points to allow for prop strikes on the Beech. Now, how can I get the rear end to stop sinking so low after making a wheels up landing?

Also, how do I move the center of gravity forward in an aircraft CFG file (not for the Beech)?

Thanks
 
Now, how can I get the rear end to stop sinking so low after making a wheels up landing?

The Beech's contact points are as follows:-

Code:
[contact_points]
max_number_of_points = 10

//point.0 = 1, -19.904,  0.000, -0.637, 2200, 0, 0.33, 45, 0.51,  2.0, 0.50, 3, 5, 0, 139, 175.2
//Replace contact_point.0 below with the one above if you want a steerable tailwheel.  You may comment out the one below with //, and activate the one above by removing the //

point.0 = 1, -19.904,  0.000, -0.637, 2200, 0, 0.33, 180, 0.51,  2.0, 0.50, 3, 5, 0, 139, 175.2
point.1 = 1,   2.890, -6.417, -5.987, 2200, 1, 0.8,    0, 1.15,  1.1, 0.50, 5, 5, 2, 139, 175.2
point.2 = 1,   2.890,  6.417, -5.987, 2200, 2, 0.8,    0, 1.15,  1.1, 0.50, 5, 5, 3, 139, 175.2
point.3 = 2,  8,     0,     -3,     1000, 0, 0,      0, 0,       0,    0, 0, 0, 4
point.4 = 2,   -1,     0,     -1.4,   3000, 0, 0,      0, 0,       0,    0, 0, 0, 4
point.5 = 2,    0,-23.495,     0.42,  1200, 0, 0,      0, 0,       0,    0, 0, 0, 5
point.6 = 2,    0, 23.495,     0.42,  1200, 0, 0,      0, 0,       0,    0, 0, 0, 6
point.7 = 2, -21.904,  0,      3,     1200, 0, 0,      0, 0,       0,    0, 0, 0, 9
point.8 = 2, -16.6,    0,      6.4,   1200, 0, 0,      0, 0,       0,    0, 0, 0, 9
point.9 = 2,   8.2,    0,      1,     1200, 0, 0,      0, 0,       0,    0, 0, 0, 4

The rear scrape points (.7 and .8) are apparently for the fuselage end and the height of the fins, so I'd suggest adding another scrape point very close to the rear wheel (point.0).

Increase max_number_of_points to 11 and add the following line to the list:-

Code:
point.10 = 2, -19.904,  0.000, -0.2, 1200, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

The height can be adjusted by editing the fourth number in that line (-0.2) if need be.

Also, how do I move the center of gravity forward in an aircraft CFG file (not for the Beech)?

The CoG is governed by several things and they're all in the [WEIGHTS AND BALANCE] section. If you want to alter the position with reference to the model, but not modify the flight behaviour, alter reference_datum_position: the first number will move it forward or back from the model centre. If you fancy messing with the actual flight behaviour, the three CG figures should drive you crazy in a matter of moments. As a matter of interest, many of the stock models have the model centre at the spinner tip, rather than the actual CoG. Weird!

Code:
[WEIGHT_AND_BALANCE]
max_gross_weight = 8750
empty_weight = 5527
reference_datum_position = 0, 0, 0
empty_weight_CG_position  = 0, 0, 0
CG_forward_limit = .21
CG_aft_limit = .33

Have fun! :mixedsmi:
 
Back
Top