Cessna U206G Soloy Turbine Pac for FSX and P3D released

Status
Not open for further replies.
So looks like VH-CZR has/had two version:
skydive bigwheel version with 3 blades and normal wheels with big door and with 5 blades.
 
Downloaded earlier this week and spent three days flying the different versions offered and found this Cessna-Soloy a brilliant aircraft to fly, once trimmed out with hands off it remains an extremely stable platform and turns, landings and take-off are a delight.:applause:

Found that it helps if the aircraft is weaved slightly during taxying due to the hump in the nose which blights part of the forward view and also found that to start taxying open the throttle slightly and once the aircraft moves it is easier to use the prop lever to increase or decrease speed whilst taxying to/from the runway.

Really enjoy flying this aircraft and like to thank all of those who worked hard to release this and looking forward to many hours of enjoyable flying ahead.

Regards
Nigel.
 
nice little aircraft here! Thank you!

I have an issue with the HSI though, not sure whats caused it but its stuck and wont rotate as the aircraft turns.
 
nigelhj said:
Downloaded earlier this week and spent three days flying the different versions offered and found this Cessna-Soloy a brilliant aircraft to fly, once trimmed out with hands off it remains an extremely stable platform and turns, landings and take-off are a delight.:applause:

Found that it helps if the aircraft is weaved slightly during taxying due to the hump in the nose which blights part of the forward view and also found that to start taxying open the throttle slightly and once the aircraft moves it is easier to use the prop lever to increase or decrease speed whilst taxying to/from the runway.

Really enjoy flying this aircraft and like to thank all of those who worked hard to release this and looking forward to many hours of enjoyable flying ahead.

Regards
Nigel.
Click to expand...


Im still trying to figure out how to stop the float plane version once landed. I chop throttles and put propeller pitch to zero and it still will taxi at 30 knots on water. It will only stop if I kill the fuel.
 
I use my mixture control as a condition lever (didn't change setting it's just what the sim uses it as) and reduce the condition to around a taxi level once landed and it stips pretty quick. Also added a little drag to the float model.
 
ejoiner said:
Im still trying to figure out how to stop the float plane version once landed. I chop throttles and put propeller pitch to zero and it still will taxi at 30 knots on water. It will only stop if I kill the fuel.
Click to expand...

Hmmm, strange, I havent problem like this. Throttle back and 10-15 knots for taxi. Sametimes I use brake (both) to slow down and you can take all control : ).
 
P3D v3.3 errors

I am having problems using this in p3d v3.3, I installed into my p3d system but when I start up the system (fresh start going directly to the soloy) I repeatedly get a dialog that pops up that says

Error Encountered
MMSystem - Unspecified Error
Full Error Code 0x88780078
Location 10
File

I also get a green message bar across the top that says:

[1008] ERROR: Thread: DirectSoundCreate() failed. br=0x88780078

The only thing different about my system that stock is I have a lot of ORBX scenery installed and I setup a folder outside of the base install folder where my custom aircraft are installed.

EDIT:

I just tried it in FSX, it asked if it can trust the sound guage and then gave me the same error dialog as above and FSX quit, so its not just P3D related.
Click to expand...
Sorry, my bad, it was my flakey sound card again that stopped working, power off, power on fixed it. Sorry for the distraction.
 
Last edited:
Ok, near done, I decided to do standard version. Please notice the new prop textures 5 blades propeler. :wavey:

206GVH1jp_arnnsps.jpg


206GVH2jp_arnnshe.jpg


206GVH3jp_arnnsha.jpg
 
Status
Not open for further replies.
Back
Top