Convair Delta Wing Test

[Milton Shupe]

Rick

It's the exact same one in the download. Haven't messed with it. Can't attach it says "invalid file". I'm running FSX Steam Edition.

The Old MSgt

You would have to put it in a folder, zip it, then attach.

 

[fliger747]

Always available for surprise but the first line not having // does not refer to any properties and if the plane loads should not disable anything.

If someone with AFSD would check if the plane is sensing throttle movement and developing thrust in the "Engine" tab it would be helpful. Very difficult to troubleshoot an issue on your system from here.

If you do not have it, very useful for many things in evaluating aircraft performance in real time.

http://sors.fr/aero/designer_pilot_utilities.html

Thanks!

 

[oldmsgt]

Here is my panel.cfg file as requested (Thanks Milton) Yes Rick, I have XMLTools installed.

The Old MSgt

 

[Flyboy208]

Thank you so much Milton and Team for this X plane. No issues for me at all. Loaded into FSX-A with no problem. Flies very well for me. Just need to do a long approach into Edwards AFB. Landed perfect on the first attempt. Beautiful textures by Rick ! Mike

 

[Seahawk72s]

Similar issue..

I am seeing the same issue as oldmsgt. I am using FSX-A.
About 20kts max at full throttle. I too tried replacing the aircraft.cfg from fliger747 and then commented out the "brakes" section with no effect. Flew Jan's "SF8_F-86EF_Sabre" prior with no issues.

Attached is AFSD screen shot shown using joy stick throttle.
When using F1-F4 keys I show 0-100% throttle (and 20kts. max)



Thanks...

 

[Milton Shupe]

I am seeing the same issue as oldmsgt. I am using FSX-A.
About 20kts max at full throttle. I too tried replacing the aircraft.cfg from fliger747 and then commented out the "brakes" section with no effect. Flew Jan's "SF8_F-86EF_Sabre" prior with no issues.

Attached is AFSD screen shot shown using joy stick throttle.
When using F1-F4 keys I show 0-100% throttle (and 20kts. max)



Thanks...

I just mirrored your Jet Engine numbers in AFSD without issues. Strange one ...

 

[fliger747]

What did AFSD show for engine thrust vrs Throttle position??

 

[Milton Shupe]

What did AFSD show for engine thrust vrs Throttle position??

For me, under Ground Dynamics, I show:

Gross Thrust = 5835
Thrust = 5834
EX Thrust = 2841

Note I was carrying more speed; was trying to get all my engine numbers close to his.

 

[fliger747]

Note the ground friction number!

Wonder what is causing that?

 

[Milton Shupe]

Note the ground friction number!

Wonder what is causing that?

Weight, low tire pressure, and textured concrete.

You should look at a loaded 747 ground friction!

 

[Sundog]

Flew it in P3Dv4, loved it. The main issue for me is after high alpha the stall message comes on and doesn't go out on the lower right part of the screen, but it didn't really bother me. Just saying. This airplane is a lot of fun to fly and my first landing wasn't bad, but I thought I had greased it on only to find I was about a foot above the runway when I dropped it on. Oops. It was still in one piece. Nice work everyone.

 

[Seahawk72s]

a little more info.

A couple more AFSD screen shots.

 

[fliger747]

A quick test this morning (off to hockey in a few minutes) shows that the max braking figure is about -5500 lbs, measured rolling resistance in a normal takeoff is about -650 lbs. As i was able to successfully takeoff with the parking brake set, apparently the max braking is greater than the parking brake?

A possibility is that the braking could be reversed in the aircraft controls section in the sim? Ie. released when for instance the trigger is pulled if that is where it is assigned?

No braking events are assigned in the .Air file currently, auto brake etc.

Try beginning a flight in the air to confirm we have a brake/ground friction issue. You have not modified ground friction in your sim? FS9 had higher ground friction and some people like this!

Cheers: T

 

[Seahawk72s]

Switched in flight from an F-86, aircraft went noze up until speed dropped from around 290kts to 30 kts.
Even with full power aircraft dropped and never regained any speed above 30 or so.

Thanks...

 

[blanston12]

I gave it a try last night and it flew quite well, the stall warning was on the whole time. It landed easily but the brakes took a long time to stop it. I would add ‘Convair’ to the title parameters.

 

[Milton Shupe]

Hi Joe,

Thanks for the feedback.

Yes, the stall warning is a"feature" we hope to remove. No affect of flight that we can detect but a nuisance that may have unseen consequences.

Good recommendation; done.

 

[Milton Shupe]

Got a friend at the local airport who claims he can "fix what's broke".

We shall see.

 

[Milton Shupe]

For those with take off issues, could you try swapping the panel for another single engine jet? That might eliminate the possibility that a gauge/panel issue is causing this problem.

EDIT: Tested and the problem still exists. So, ignore this request now. Thanks

 

[Bjoern]

Users with issues should check their FSUIPC for any ground friction mods.

Aircraft.cfg contact points are valid, I assume?

EDIT: Made the suggested changes to the panel/sound folders and panel.cfg and it works correctly. Thanks

Yeehaw!

 

[WarHorse47]

I assume these latest issues are more with P3D?

I've encountered no issues with FSXA, but did note there were no lights externally or internally.

My last flight was uneventful. I took off from Edwards on Rwy 4R and climbed to 40,000 feet at full AB. After turning 180 degrees and headed back to KEDW, I watched my fuel which was at 50%. I landed with the "Bingo Fuel" warning. Hard to slow it down to a reasonable landing speed, so I took up most of the runway before stopping and taxing back to parking. Lots of fun.