• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Please see the most recent updates in the "Where did the .com name go?" thread. Posts number 16 and 17.

    Post 16 Update

    Post 17 Warning

Flying the IRIS Harrier in FSX

falcon409

falcon409

SOH-CM-2025
I know there have to be a few of us out there that have converted the Harrier to FSX. I installed Rob's VTOL conversion package, however I have no more "lift" capability now than I did before I installed it. Nothing seems to have changed.

I went back through the installation and general operating instructions that Rob included. . .(very extensive explanations too) and everything seems to be in order:
I have an updated payware version of FSUIPC
I have the folder rcb_gauges in the panel folder
I replaced the original panel.cfg with the revised version
I replaced the original aircraft.cfg file with the revision
I placed the new "cab" file in the FSX gauges folder

FSUIPC shows up in the "Addons" dropdown inside FSX
The flaps/Nozzle red line indicator shows correct flaps/nozzle position

Here is a shot of the Harrier at full throttle:
 
I don't know if this will help or not, but what you did seems to be a lot more complicated than what I did. I was using the freeware versions of both, and they worked fine. I also used FSUIPC 4 for their JSF.
 
Try getting the weight of the aircraft under 21,000lbs. The thrust should be enough to lift the Harrier off the ground under that weight.
 
Flyboy, The current weight is just a tad above 11,000. . .I went through that checklist as well, even though I didn't post that here. If the image I show in my post was a video. . .there wouldn't be any change. . .it just sits on the ground with the engines running full mil and it doesn't show any sign of wanting to lift.

James, I'm not sure what you mean by the "freeware versions of both". . .if you mean the original cfg and airfile, then I used those first with the same results, that's why I mentioned that I saw no change from the original. Also, the FSUIPC version I use is the most recent updated payware version, as I said.
 
May be a silly question, but you're not using the FS9 version of the gauge instead of the FSX version?
 
The way I get the harriers to fly right is to install the freeware FSUIPC . But it seems not to activate,but it does . Then I extract the hover gauge in to the main FSX folder . It ask to over ride I click yes . When I open FSX and pick the harrier it as to run the new installed software,I click yes and away I go . I do the same thing for the Alphasim V22 and the IRIS F35B . The hover gauge are rcb10 andrcb11 something like that . Hope it helps .
 
I downloaded the FSX VTOL gauge by Rob Barendregt. . .made specifically for the IRIS Sigma Harrier. Already mentioned twice in my posts, I am using the payware version of FSUIPC which I purchased years ago and continue to upgrade as they come available, so it's not that I don't have it installed.

Also already mentioned, the Harrier is not overweight, it's sitting right now at just under 11,000. SO, with everything installed correctly, full nozzle deflection beyond 80 degrees and full flaps and throttle at full mil. . .the harrier sits in the middle of the ramp, engulfed by the exhaust and fumes and doesn't budge.
 
Empty the two external tanks, there should be four in the fuel menu, empty two and it will VTOL. FSuipc should not be the problem!
P.s. have you fixed the HUD anomoly Ed?
 
peter12213 said:
. . . . .P.s. have you fixed the HUD anomoly Ed?
Click to expand...
I've looked at the textures, but only see one "glass" texture and no changes I made affected the HUD. I went through the mdl file looking at LOD's that might be the culprit, but nothing I did made any difference either.:salute:
 
AndyE1976 said:
Is there a fix for the opaque hud?
Click to expand...

The HUD is only opaque with any lights on. Unfortunately, the VTOL smoke effects use lights as a trigger sending the HUD opaque. You can disable the Harrier_GR7!Effect Controller in the panel.cfg but then you'll loose the smoke effects.
 
DaveWG said:
The HUD is only opaque with any lights on. Unfortunately, the VTOL smoke effects use lights as a trigger sending the HUD opaque. You can disable the Harrier_GR7!Effect Controller in the panel.cfg but then you'll loose the smoke effects.
Click to expand...
Which is well worth the effort to get the HUD back. . .I don't care about the effects anyway, I'm in the VC keeping the ship level, lol

Thanks Dave!!:salute:
 
Hi Ed,

After our extensive communications on the Skycar, I'm a bit surprised :mixedsmi: you haven't Emailed me directly with your problem on this Iris Harrier; You certainly may ....! :)

Off hand, with what I read in your first post:
Make sure that the subfolder you place my stuff in, is spelt as "rcb-gauges" , NOT "rcb_gauges"

:ernae: Rob
 
rcbarend said:
Hi Ed,
After our extensive communications on the Skycar, I'm a bit surprised :mixedsmi: you haven't Emailed me directly with your problem on this Iris Harrier; You certainly may ....! :)

Off hand, with what I read in your first post:
Make sure that the subfolder you place my stuff in, is spelt as "rcb-gauges" , NOT "rcb_gauges"
:ernae: Rob
Click to expand...
Hi Rob, still flying the Skycar by the way.
That rcb_gauges was a typo. . .the actual gauge folder is correct.

I took Peter's advice and emptied the external tanks (which put it below 10,000lbs) and after some coaxing (it still doesn't lift off as you advance to full throttle), it will finally lift off. For landing however, I remember being able to slowly settle down on the main gears as I reduced the power setting, but now, once I go to full flaps and nozzle deflection, it drops like a rock even at full throttle.

I didn't e-mail directly because I didn't want to bother you with this. . .I'm sure. . .somewhere in all this mess it's something I did, lol. I know your work and so I have complete confidence that it isn't on your side.:salute:
 
falcon409 said:
.........For landing however, I remember being able to slowly settle down on the main gears as I reduced the power setting, but now, once I go to full flaps and nozzle deflection, it drops like a rock even at full throttle.
Click to expand...
Hi Ed,

That still sounds like something isn't installed properly, because that shouldn't happen.
Since you have the Skycar working, FSUIPC must be working Okay.
If you Email me an overview of the folderstructure for the Harrier, your aircraft.cfg and panel.cfg, I'll have a look if you want.

ALso note two other things:
1. Look at the TOTAL gross weight of the aircraft. (so empty weight + payload + fuel).
You can find that number in the fuel/payload menu, and should be between 15000 and 21000 lbs.
2. For VTOL/hovering, do not use Full Flaps (this places the nozzles in the FullBrakingStop position, ie. 98 degrees rotated) but FullFlaps minus 2. This sets the nozzles to 90 degrees. Although this doesn't explain the problem you have.


Cheers, Rob

PS. As far as my support is concerned: 99.9% of all problem support requests I get via Email, appears to be caused by a user doing something wrong (usually in installing it), so there no reason to hesitate contacting me ... LoL
 
DaveWG said:
The HUD is only opaque with any lights on. Unfortunately, the VTOL smoke effects use lights as a trigger sending the HUD opaque. You can disable the Harrier_GR7!Effect Controller in the panel.cfg but then you'll loose the smoke effects.
Click to expand...

I lined that one out and the HUD is still foggy. I do see a bit of a difference
(less fog) when lights are switched on/off.
 
You must log in or register to reply here.
Back
Top