• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

JF Canberra PR9 is out

dvj said:
I have the same problem. The configuration suite change to the steering mode by clicking the hot spot on the panel -- did nothing. Just changed the contact point number 7 in the config file, let's see if that fixed it. If not, it's off to JF support. Strange these random bugs. BTW, Frames always above 32, max sliders, full FTX, REX, core i7 extreme, 32GB memory, GTX 780. Smooth as silk. Stunning visuals and sound.
Click to expand...

Please note that the clickspot on the trim panel performs a different function to the options in the configuration tool. The clickspot simply allows you to use your joystick rudder axis to apply differential braking, it does not enable a direct-steer nosewheel like the tool does.

The manual covers this (in the section that covers the trim panel).

Edit - a customer has just noticed that the trim panel clickspots are incorrectly labelled (reversed) on the manual image. The nosewheel clickspot is the lower of the two.
 
Alpha Two Zero said:
Hi,
I can't get the Canberra to close down. I click the Lightning bolt Hatch opens the navigator front opens but the engines just keep spooling up.
Click to expand...

Please drop the support team a ticket and they'll look into it. If you have altered your default flight (that appears when you first select FREE FLIGHT in FSX) please make sure to tell them.
 
Martyn said:
Please note that the clickspot on the trim panel performs a different function to the options in the configuration tool. The clickspot simply allows you to use your joystick rudder axis to apply differential braking, it does not enable a direct-steer nosewheel like the tool does.

The manual covers this (in the section that covers the trim panel).

Edit - a customer has just noticed that the trim panel clickspots are incorrectly labelled (reversed) on the manual image. The nosewheel clickspot is the lower of the two.
Click to expand...

Changed the contact point to 90. nosewheel steering just fine now.
 
Till now I fly C.Pr9 only in P3Dv2.1, Today install in FSX - wow great FPS here, stable 30 (blocked) in any condition. A little worse in P3D but like here shadows.
Just one question - if I have installed the model in X and in P3D - if I changed something in Analysis Tool I will do it for both sims?

Pic from M.FSX:

Screenshot21233_zps30db10be.jpg~original
 
Just incase anyone else see this. Cold start: Black smoke at end of wings, not aligned to engines.
 
Absolutely beautiful airplane. Running out of available memory about every other flight but that's my problem. I assume if I'm getting this error (see pic) the "Canberra_Flight_Analysis.exe" tool is not available to me...?
 
And I noticed some of bugs in P3Dv2.1:

1/ A conventional slip ball is located below the HGU - doesnt work at all in P3D, in FSX yes:

Nowy-1_zps8af2806d.jpg~original


2/ FM / Rudder problem. After the start rudder dosent work so its a very difficult to turn or do correction for example for landing. In FSX is ok.

3/ Too dark in P3D campared to FSX inside cocpit (red lights on):

 
WarHorse47 said:
Yep.
2014-2-20_9-47-7-692_zpsab3f1657.jpg
Not sure what the starter smoke is aligned with.
Click to expand...
The smoke effects is aligned with the "virtual" engines defined in the aircraft.cfg. I assume they've been moved outward to give the FD the pronounced asymmetric effect when flying on one engine.
 
Many bugs so for Pricing
Has a couple of days, but I still can not steering the airplane on the ground
The Canberra Flight Analysis Tool CTD !
The effects of smoke in the wrong place
In a word ..... :pop4:
 
zsoltquack said:
Many bugs so for Pricing
Has a couple of days, but I still can not steering the airplane on the ground
The Canberra Flight Analysis Tool CTD !
The effects of smoke in the wrong place
In a word ..... :pop4:
Click to expand...

Canberra Flight Analysis Tool helps a lot for nose stering ( FAQ for this: http://www.justflight.com/supportfaq/canberra-pr9 ) - I havent any CTD of this tool in P3D and FSX but perhaps it needs two version. I installed Canberra for FSX and P3D and have only one (perhaps for the last installer) Canberra Flight Analysis Tool on Just Flight Folder in Star>Programms. For this kind of situation it must be two (or if I change something programm will do it for both Canberra version? Dont know yet...)
 
Last edited:
zsoltquack said:
Many bugs so for Pricing
Has a couple of days, but I still can not steering the airplane on the ground
The Canberra Flight Analysis Tool CTD !
The effects of smoke in the wrong place
In a word ..... :pop4:
Click to expand...

Zsolt, you can fix the black cartridge startup smoke: In the aircraft.cfg, change the startup = fx_canb_start entry like this:

[EFFECTS]
wake = fx_wake
water = fx_spray
dirt = fx_tchdrt
concrete = fx_sparks
touchdown = fx_tchdwn_m,1
startup = fx_dummy

Thought I read somewhere the PR9 did not use starter cartridges, in the RAF they used AVPIN liquid. The civil Midair Canberra in the JF pack got electric starters.
The funny thing is the fx_canb_start.fx file is not included in the JF installer but it is used in the Flying Stations Canberra series, so I guess everyone who has those installed will see the black cartridge puffs.
 
Zolt, change the 7th entry in contact points column 1, from 180.00 between 90 - 100.

I answered that a couple of posts before......



zsoltquack said:
Many bugs so for Pricing
Has a couple of days, but I still can not steering the airplane on the ground
The Canberra Flight Analysis Tool CTD !
The effects of smoke in the wrong place
In a word ..... :pop4:
Click to expand...
 
Not sure that your list constitues 'many bugs' but as long as you have submitted a support ticket we'll be able to get things sorted out for you.

With regards to the start effect, I have no idea why you are seeing a cartridge start effect as that's not something we included. We'll look into that. The engines are not aligned to their location on the model for FDE reasons but that won't matter if you only have our custom effects.
 
Just suggestion (not read manual yet). In the start I have always engines running on. Is it possible to add for this 2D panel: Cold & Dark function?



Btw. Its not a screen of Me-262 !!! :adoration:

New shot:

Screenshot38747_zps0e281693.jpg~original
 
Amazing pic YoYo!

The aircraft should load in a ready for takeoff state. Clicking the power icon should then set it to a cold and dark state.
 
You must log in or register to reply here.
Back
Top