• There seems to be an uptick in Political comments in recent months. Those of us who are long time members of the site know that Political and Religious content has been banned for years. Nothing has changed. Please leave all political and religious comments out of the forums.

    If you recently joined the forums you were not presented with this restriction in the terms of service. This was due to a conversion error when we went from vBulletin to Xenforo. We have updated our terms of service to reflect these corrections.

    Please note any post refering to a politician will be considered political even if it is intended to be humor. Our experience is these topics have a way of dividing the forums and causing deep resentment among members. It is a poison to the community. We appreciate compliance with the rules.

    The Staff of SOH

  • Server side Maintenance is done. We still have an update to the forum software to run but that one will have to wait for a better time.

What does this mean...?

gamemaster406

Charter Member
I'm going to install update 1.20 for ETO and the readme tells me to [FONT=&quot]

Note: Be sure to place your CFS3 ETO Expansion Theater in ERA 1

[/FONT]
[FONT=&quot]What the heck does that mean?

-Mike
[/FONT]
 
Note: Be sure to place your CFS3 ETO Expansion Theater in ERA 1

Before you update ETO, open ETO Select ERA 1 the Spanish Civil war. When you get to where the pilot is waiting at the airfield close ETO. Then Install the upgrade.
 
I'm going to install update 1.20 for ETO and the readme tells me to

[FONT=&quot]Note: Be sure to place your CFS3 ETO Expansion Theater in ERA 1[/FONT]

[FONT=&quot]What the heck does that mean?[/FONT][FONT=&quot]

[FONT=&quot]-Mike[/FONT]
[/FONT]

:kilroy:Gamemaster406, it means that CFS3 ETO expansion 1.0 must be started in Era 1 and exited before installing CFS3 ETO Expansion Cumulative Update 1.20. You should also set the ETO Spawn Selector to 1 before installing 1.20.

Here is the full procedure for installing ETO:

1. You need a clean, fully-updated (3.1 and 3.1a) vanilla (unmodded) install of CFS3 in order to install CFS3 ETO Expansion Rev 1.0.exe.

2. Install CFS3 ETO Expansion Rev 1.0.exe per readme instructions. After ETO 1.0 has been installed properly and run at least once, start it again in Era 1 and exit, then set the ETO Spawn Selector to 1.

3. Now install CFS3 ETO Expansion Cumalative Update Rev 1.20.exe per readme instructions. After this, you should be good to go.

Note: Failure to follow the three primary steps above will result in a corrupted, or otherwise messed-up ETO install.

I hope this helps.:d
 
:kilroy:Gamemaster406, it means that CFS3 ETO expansion 1.0 must be started in Era 1 and exited before installing CFS3 ETO Expansion Cumulative Update 1.20. You should also set the ETO Spawn Selector to 1 before installing 1.20.

Here is the full procedure for installing ETO:

1. You need a clean, fully-updated (3.1 and 3.1a) vanilla (unmodded) install of CFS3 in order to install CFS3 ETO Expansion Rev 1.0.exe.

2. Install CFS3 ETO Expansion Rev 1.0.exe per readme instructions. After ETO 1.0 has been installed properly and run at least once, start it again in Era 1 and exit, then set the ETO Spawn Selector to 1.

3. Now install CFS3 ETO Expansion Cumalative Update Rev 1.20.exe per readme instructions. After this, you should be good to go.

Note: Failure to follow the three primary steps above will result in a corrupted, or otherwise messed-up ETO install.

I hope this helps.:d

Ahh... I see but I can't switch spawn modes as you read before in my other thread, so I'm pretty much stuck in 1.0 till I figure out how to fix that...
 
Back
Top