• Please see the most recent updates in the "Where did the .com name go?" thread. Posts number 16 and 17.

    Post 16 Update

    Post 17 Warning old domain name stealing credentials

  • Special Server Maintenance

    Just when you think you have everything running some what better...

    You get a message from the Hosting company. Short story they need to move us to a new server. I have been working with them to plan a good date for all concerned. Here is what we have come up with as a schedule.

    1. November 4th 17:00 -5UTC shut off the forums and start backup proceedures. During this time there will be no access to the forums or the Resource Section.
    2. November 5th Continue with Backups and download same until complete.
    3. November 6th 7:00 turn over server to hosting company to move system to new server
    4. November 7th - 8th restore backups and upgrade forum software.

    If all goes well we should be back online on November 8th.

    To keep you updated we will post updates on AVSIM forums.

    Thank you for your support.

C-47 V3 - Disable ILS Audio

C

cfelix

Members +
Hi,

I am loving this plane! Thanks for all the hard work. One small problem I'm having is that I can't seem to disable the Morse Code audio when on approach with NAV1 tuned to the ILS. I've tried middle-clicking on the NAV1 label in the Monitor panel and made sure that all switches are set to mute on the intercom panel. The only way I could get it to stop was to change frequency. I'm probably just missing something very simple but I'd appreciate any advice. Thanks.

Charlie - KSBP
 
cfelix said:
Hi,

I am loving this plane! Thanks for all the hard work. One small problem I'm having is that I can't seem to disable the Morse Code audio when on approach with NAV1 tuned to the ILS. I've tried middle-clicking on the NAV1 label in the Monitor panel and made sure that all switches are set to mute on the intercom panel. The only way I could get it to stop was to change frequency. I'm probably just missing something very simple but I'd appreciate any advice. Thanks.

Charlie - KSBP
Click to expand...

Yes, the intercom panel is still a work in progress.
 
morse code

Had the same experience, went through all aircraft and found DME turn on in a third party download, turned it off and situation corrected. Tried to turn DME of in default aircraft no response had to find the main source, hope this helps
 
Have had the same issue with the Morse code bipping and found that turing the DME off in fx the default Cessna 172 cures it, hastle though to have to change planes to cure the annoying bipping.

Berlopez
 
Berlopez said:
Have had the same issue with the Morse code bipping and found that turing the DME off in fx the default Cessna 172 cures it, hastle though to have to change planes to cure the annoying bipping.

Berlopez
Click to expand...

I had the same Morse code beeping :(
Thanks to Monitor panel, I discoverd that Nav2 Ident was on (but Voice on the gauge). Could switch it off with Monitor panel.

Somewhere, I wrongly mentionned beacon switch not working - I confused with the "Anti Collision" switch (some cockpit use this name instead of "Beacon").
My bad - :culpability:

Gérard
 
In Monitor > Avionics, if the NAV1 is highlighted you hear the Marker Morse code. Middle-click to toggle ON/OFF (cp. tooltip).

Somewhere, I wrongly mentionned beacon switch not working - I confused with the "Anti Collision" switch (some cockpit use this name instead of "Beacon").
My bad - :culpability: Gérard
Click to expand...

The beacon switch is only functional if the exterior model has a beacon (or two), in other words, if the model= line references either C47_2 or GAF. The default model is from a pre-beacon era; it hasn't got one.
 
You must log in or register to reply here.
Back
Top