Spad54
SOH-CM-2025
That's beautiful!
GAS C3B Stearman FSX FSXSE P3D
- Thread starter Spad54
- Start date
That's beautiful!
Spad54
SOH-CM-2025
Panel cfg. file error
In final prep for commercial release discovered an error in the panel config file. If you have out UPF-7 it would be hidden from you. Here are the edits that will assure that the correct entries are present to properly load the avionics.
FSX FSXSE P3D 1-3 32 Bit
//--------------------------------------------------------
[Vcockpit01]
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B
gauge00=GAS_Sound!FBGS_XMLSound, 0,0,1,1,SimObjects\\Airplanes\\GAS_Stearman_C3B\\sound\\Stearman#19
gauge01=GASC3B!altimeter, 220,300,100,98
//--------------------------------------------------------
[Vcockpit02]
//file=gaugemap_C3B_1.bmp
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B_1
gauge00=GASC3B!altimeter, 220,300,100,98
gauge01=fs9gps!gps_295, 6,88,271,177
gauge02=GASC3B!ATC, 325,10,200,61
gauge03=GASC3B!COMM1, 13,9,120,67
gauge04=GASC3B!COMM2, 142,7,118,69
//------------------------------------------------------------------------------
P3D 1-4 64 bit
//--------------------------------------------------------
[Vcockpit01]
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B
gauge00=GAS_Sound_64!FBGS_XMLSound, 0,0,1,1,SimObjects\\Airplanes\\GAS_Stearman_C3B\\sound\\Stearman#19
gauge01=GASC3B!altimeter, 220,300,100,98
//--------------------------------------------------------
[Vcockpit02]
//file=gaugemap_C3B_1.bmp
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B_1
gauge00=GASC3B!altimeter, 220,300,100,98
gauge01=fs9gps!gps_295, 6,88,271,177
gauge02=GASC3B!ATC, 325,10,200,61
gauge03=GASC3B!COMM1, 13,9,120,67
gauge04=GASC3B!COMM2, 142,7,118,69
In final prep for commercial release discovered an error in the panel config file. If you have out UPF-7 it would be hidden from you. Here are the edits that will assure that the correct entries are present to properly load the avionics.
FSX FSXSE P3D 1-3 32 Bit
//--------------------------------------------------------
[Vcockpit01]
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B
gauge00=GAS_Sound!FBGS_XMLSound, 0,0,1,1,SimObjects\\Airplanes\\GAS_Stearman_C3B\\sound\\Stearman#19
gauge01=GASC3B!altimeter, 220,300,100,98
//--------------------------------------------------------
[Vcockpit02]
//file=gaugemap_C3B_1.bmp
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B_1
gauge00=GASC3B!altimeter, 220,300,100,98
gauge01=fs9gps!gps_295, 6,88,271,177
gauge02=GASC3B!ATC, 325,10,200,61
gauge03=GASC3B!COMM1, 13,9,120,67
gauge04=GASC3B!COMM2, 142,7,118,69
//------------------------------------------------------------------------------
P3D 1-4 64 bit
//--------------------------------------------------------
[Vcockpit01]
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B
gauge00=GAS_Sound_64!FBGS_XMLSound, 0,0,1,1,SimObjects\\Airplanes\\GAS_Stearman_C3B\\sound\\Stearman#19
gauge01=GASC3B!altimeter, 220,300,100,98
//--------------------------------------------------------
[Vcockpit02]
//file=gaugemap_C3B_1.bmp
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B_1
gauge00=GASC3B!altimeter, 220,300,100,98
gauge01=fs9gps!gps_295, 6,88,271,177
gauge02=GASC3B!ATC, 325,10,200,61
gauge03=GASC3B!COMM1, 13,9,120,67
gauge04=GASC3B!COMM2, 142,7,118,69
WarHorse47
SOH-CM-2024
Thanks. Trying it now in FSXA. Got an error message. There is an extra space in the word sound for gauge00= for [VCockpit01] that needs to be removed.
I also noticed that the altimeter gauge is repeated for both VCockpits. Intentional?
gray eagle
SOH-CM-2025
Is this correction applicable for this model only? (see link)
http://www.sim-outhouse.com/sohforums/showthread.php/118009-GAS-WACO-UPF-7-SOH-Sale
Was confused a little as this was posted on the C3B thread. I assume no corrections for the C3B.
Last edited:
Spad54
SOH-CM-2025
This only applies to the C3B. The duplicate altimeter entry should be eliminated the thread has been updated. No worries for the UPF-7. Also make sure that the GASC3B.cab file in the panel folder is copied and placed in the main Gauges folder for all simulators. I used the UPF-7 panel.cfg file for adding the avionics as a last minute addition and in my haste left those references behind. I did not notice the problem because that folder was already in my Gauges folder and the sim found what it needed. When I installed it to a second computer that did not have the UPF-7 installed the error made itself evident. I'm sorry for the bother.
gray eagle
SOH-CM-2025
I noticed that too.
gray eagle
SOH-CM-2025
My Vcockpit 01 entry looks same as your corrections for (P3D V4.5)
This is my original entry:
[Vcockpit01]
Background_color=0,0,0
size_mm=512,512
visible=0
pixel_size=1024,1024
texture=$panel_C3B
gauge00=GAS_Sound_64!FBGS_XMLSound, 0,0,1,1,SimObjects\\Airplanes\\GAS_Stearman_C3B\\sound\\Stearman#19
gauge01=GASC3B!altimeter, 220,300,100,98
Using winmerge the files are identical (for the P3D applicable entries)
https://winmerge.org/?lang=en
Last edited:
gray eagle
SOH-CM-2025
Reread notice
Edit: I reread the bit about:
The duplicate altimeter entry should be eliminated - so noted.
Edit: I reread the bit about:
The duplicate altimeter entry should be eliminated - so noted.
Last edited:
Spad54
SOH-CM-2025
Product Update
The product installer has been updated. All you you good folks who purchased the model will receive an email to that extent. Its copied here for your convenience.
Your recently purchased product has been updated to include a transparent glass option, corrected Panel.Cfg entries, and .cab files in the Gauges folder. To access please redownload the product using the link provided for you initial purchase.
Finally the sales period has been extended as additional week.
Thanks all.
The product installer has been updated. All you you good folks who purchased the model will receive an email to that extent. Its copied here for your convenience.
Your recently purchased product has been updated to include a transparent glass option, corrected Panel.Cfg entries, and .cab files in the Gauges folder. To access please redownload the product using the link provided for you initial purchase.
Finally the sales period has been extended as additional week.
Thanks all.
gray eagle
SOH-CM-2025
Hi,
I received the notice (email) of the update, thanks.
What you mentioned ^ about the transparent glass option has me curious as to what would have to be done to revert to the clear glass like it was on original release?
I like the glass the way it is now; I did not see any read me to clarify this and just wanted to ask.
I enjoy flying this bird and all the textures are very nice.
Thank you for such a nice looking aircraft.
Edit: I had the original release with the more transparent glass within the original model files; with this new release, I renamed it to distinguish it from the original release.
That way, I have the original model files for backup - but for those that didn't have the original release, what options are there to revert?
Many thanks for this latest addition! Beautiful as always. I just got an email from GAS talking about an update for the panel as well as a new .cab file. I've already downloaded the windscreen mod. Did that also have the panel and .CAB fix in it, or can I just get that from the previous entry in this thread?
Thanks.
Thanks.
