Lockheed Jetstar II

I still get the warning as well but the aircraft shows and then will load the flight. So, no more CTD at least. There is, of course no VC! It shows the Wallert Jetstar panel in 2D but only has about 3 gauges. Didn't try to fly it... Hope this can get sorted out to work in FSX! Your efforts are greatly appreciated!
 
oldmsgt said:
I still get the warning as well but the aircraft shows and then will load the flight. So, no more CTD at least. There is, of course no VC! It shows the Wallert Jetstar panel in 2D but only has about 3 gauges. Didn't try to fly it... Hope this can get sorted out to work in FSX! Your efforts are greatly appreciated!
Click to expand...

So when you move to outside you see just the lights I guess ?

If you put trottle it would accelerate ?

Thank you
 
thanks for the model update.

I have also posted this over in the P3D forum

Not sure why but I have tried the aircraft in all three sims: FSX, P3Dv4.5 and P3Dv5.2 and in all cases I get a CTD after selecting the Jetstar and initializing the sim. As some seem to find it works in P3D and it was extensively tested in P3D I am mystified as to why I would be having this happen in all three sims. Any thoughts would be greatly appreciated.
 
P3DV5.2 ONLY

Still with newest model 2 threads before same story?

I flew it 5 minutes ago in P3DV5.2- + ORBX

Did you try the 2 panel.cfg's I posted yet ?

If still I need to think longer

But it is memory heavy model-->You have enough card memory

and lets move to P3D forum. I read both

Roland
 
thunder100 said:
So when you move to outside you see just the lights I guess ?

If you put trottle it would accelerate ?

Thank you
Click to expand...

Sorry for not replying sooner, had to run a few errands. Yes, outside view is a ghost ship, only flashing red beacons. I do have sound and she will spool up and perform takeoff roll @ throttle up. After T.O. gear will retract (sounds like anyway). Didn't attempt landing due to not having flight instruments and inadequate forward view.
 
oldmsgt said:
Sorry for not replying sooner, had to run a few errands. Yes, outside view is a ghost ship, only flashing red beacons. I do have sound and she will spool up and perform takeoff roll @ throttle up. After T.O. gear will retract (sounds like anyway). Didn't attempt landing due to not having flight instruments and inadequate forward view.
Click to expand...

YES There is real life as well

Look a bit up there are new models

I hope they work- only mising is in VC overhead. That I do- if at all function- as next step

Roland
 
thunder100 said:
P3DV5.2 ONLY

Still with newest model 2 threads before same story?

I flew it 5 minutes ago in P3DV5.2- + ORBX

Did you try the 2 panel.cfg's I posted yet ?

If still I need to think longer

But it is memory heavy model-->You have enough card memory

and lets move to P3D forum. I read both

Roland
Click to expand...

Roger that - yep tried the panel cfg's you sent and I posted it to the P3D forum. Will keep to that for for future discussions. Thanks for your replay in both places.
 
Well, with the new model file there is indeed some progress made! No more visual model warning, flight loads without problem and external view is normal. In the VC as stated there is no overhead. However all the flight instruments are black holes, no display in Comm/Nav control panels and there is no view out the windscreen, only a medium blue color. Hey, getting late there, go to bed! Enough for one day, there's always tomorrow, and thanks!
 
Update fsx only

UPDATE FSX ONLY


Dear All

1.)First use these Models- they should( should as I cannot test in FSX)-show good exterior and good interior

View attachment 84879

Delete (FSX only) all other models

2.)Panel

Use this panel -->rename panel normal.cfg-->panel.cfg
put it into panel folder- overwrite = OK

View attachment 84880

3.) make test flight in FSX and pls report OK or not OK

4.) not OK

Plane loads in preview but goes CTD when you want to start flight

Use this panel -->rename panel light.cfg-->panel.cfg

Still CTD

Use this panel -->rename panel panel even more Light.cfg-->panel.cfg

Best regards

Roland

Depending on your system and which planes+ gauges you have, you will have some black holes - no gauge ( pedestal ).These are payware ones- we still have to develop for this plane. If you are good in panel cfg, you can replace them with what you have
 
Just tried the download from yesterday and the model attached in the above post. I get on loading a CTD with both. Must be a ".gau" or 32 bit gauge somewhere causing this? P3Dv4.5.

Been doing some flight testing. FDE is quite good but may have some minor adjustments.
 
Panel should look like that

smallerp1.jpg

This we try with your help to achieve (XML coding PLEASE !!!)

the light and lighter panel is easier on memory but moves away from that task

Roland
 
expat said:
Just tried the download from yesterday and the model attached in the above post. I get on loading a CTD with both. Must be a ".gau" or 32 bit gauge somewhere causing this? P3Dv4.5.

Been doing some flight testing. FDE is quite good but may have some minor adjustments.
Click to expand...

Did first beta test work - I initially sended ?

If so use the original download version - not above models ( these are FSX only )

If still CTD use in this setup the old - working panel cfg
 
Playing around in MCX with the both the exterior and interior models of the FSX versions. Adjusted the texture assignments for the interior model to use the "l" textures. In the exterior model I activated the reflective textures, adjusted the nosewheel steering from c_wheel to c_wheel_fs9 to make sure it steers in both directions.

As for the ADI issue on the co-pilots side, in mcx I don't see an assigned vc texture in that spot. Just the background texture instead of the black spots showing on the pilot side.
 
Jetstar

FWIW I loaded the Jetstar yesterday and had no problems flying the jet...so far. Will try a more detailed flight today. By the way I'm running P3Dv4 with Windows7. Most important thanks to everyone who made this possible.
 
Brian_Gladden said:
Playing around in MCX with the both the exterior and interior models of the FSX versions. Adjusted the texture assignments for the interior model to use the "l" textures. In the exterior model I activated the reflective textures, adjusted the nosewheel steering from c_wheel to c_wheel_fs9 to make sure it steers in both directions.

As for the ADI issue on the co-pilots side, in mcx I don't see an assigned vc texture in that spot. Just the background texture instead of the black spots showing on the pilot side.
Click to expand...

I would be glad to see your models

Roland
 
Things are getting a little confusing for us old guys.

I've installed the latest model folder and panel.cfg, but am still getting a CTD in FSXA. Model loads and no error message, but get a CTD and a FSX reboot.

May I suggest that all P3D feedback be posted in the P3D forum section and leave comments in this section strictly for feedback on FSX??
 
You must log in or register to reply here.
Back
Top