Bomber_12th
SOH-CM-2025
FSAddon Waco CTO at Orbx Lake Tahoe
-
Please see the most recent updates in the "Where did the .com name go?" thread. Posts number 16 and 17.
-
Special Server Maintenance
Just when you think you have everything running some what better...
You get a message from the Hosting company. Short story they need to move us to a new server. I have been working with them to plan a good date for all concerned. Here is what we have come up with as a schedule.
- November 4th 17:00 -5UTC shut off the forums and start backup proceedures. During this time there will be no access to the forums or the Resource Section.
- November 5th Continue with Backups and download same until complete.
- November 6th 7:00 turn over server to hosting company to move system to new server
- November 7th - 8th restore backups and upgrade forum software.
If all goes well we should be back online on November 8th.
To keep you updated we will post updates on AVSIM forums.
Thank you for your support.
P3D_V5 Screenshots P3D V 5
- Thread starter noddy
- Start date
TiAr
Charter Member
docjohnson
Charter Member
docjohnson
Charter Member
No problem, I saw this on the Milviz general forum:
"It flies in P3D v4.5 but I don´t see the pilot 3D figure. Overall I would say it works fine (I never tried in earlier versions to be able to detect failures).
When you install it, as P3Dv4 is not detected, installer will extract files to a temp directory. In my case it was in F:\temp0. Just copy the content to Effects, Gauges and Airplanes. Don´t overwrite files as the ones already installed would be most likely newer than the ones in the Stuka. Alternatively you can use 7-Zip to unpack the exe directly.
Autostart is not working completely, and fuel pumps are not switched on, so a periodic engine start sound will be heard. Just do a cold and dark manual start instead or check that all systems are on after the autostart."
I used the installer: MilViz_Stuka_v3.170417.exe. I don't remember having to copy any files out of a temp directory. But installed it outside of the main Prepar3D v5 root. I didn't care if the crew was visible or not, but if I remember right there was a spot on the external model (view) between the pilot and back seater on the fuselage that I clicked out of curiosity (the mouse changed as I went over it) and both figures appeared.
"It flies in P3D v4.5 but I don´t see the pilot 3D figure. Overall I would say it works fine (I never tried in earlier versions to be able to detect failures).
When you install it, as P3Dv4 is not detected, installer will extract files to a temp directory. In my case it was in F:\temp0. Just copy the content to Effects, Gauges and Airplanes. Don´t overwrite files as the ones already installed would be most likely newer than the ones in the Stuka. Alternatively you can use 7-Zip to unpack the exe directly.
Autostart is not working completely, and fuel pumps are not switched on, so a periodic engine start sound will be heard. Just do a cold and dark manual start instead or check that all systems are on after the autostart."
I used the installer: MilViz_Stuka_v3.170417.exe. I don't remember having to copy any files out of a temp directory. But installed it outside of the main Prepar3D v5 root. I didn't care if the crew was visible or not, but if I remember right there was a spot on the external model (view) between the pilot and back seater on the fuselage that I clicked out of curiosity (the mouse changed as I went over it) and both figures appeared.
Bomber_12th
SOH-CM-2025
93 years on
Bomber_12th
SOH-CM-2025
You need to have the original Spirit of St. Louis files from FS2004, plus the FSX-native converted files by Craig Richardson, attached.
